5300 Business DriveHuntington Beach, CA 92649USAPhone: 714-893-8529 FAX: 714-894-9492E mail: [email protected] or [email protected]
Page 106.0 How To Operate The C-1100V6.1 Description of Pump Output Adjustment Controls - Open the control panel door by sliding the upper and lower
CAUTIONADJUST WHILE RUNNINGDISCHARGE LINES MAY BEUNDER HIGH PRESSURE. USECARE TO PROTECT YOURSELFWHEN DISCONNECTING.MAXMIN123456789LOOSEN THE LOCK SCR
Page 126.4 - OPERATING MODE 2 - Output adjusted by 4-20 mA input signal In this mode, the pump’s motor speed is adjusted automatically based on the va
Page 134maximum value is ready to be programmed. The currently programmed maximum motor speed value is shown on the 3-DIGIT LCD.4Enter the motor speed
Page 146.5 - OPERATING MODE 3 - Output adjusted by 0-10VDC input signal In this mode, the pump’s motor speed is adjusted automatically based on the va
Page 15indicating the maximum value is ready to be pro-grammed. The currently programmed maximum motor speed value is shown on the 3-DIGIT LCD.4Enter
C-1100V6.5 - OPERATING MODE 4 - Output adjusted by frequency (Hz) input signal In this mode, the pump’s motor speed is adjusted automatically based on
C-1100VPROGRAM MODE 4minimum input valueRUNPROGRAMSTAND-BYPRIMEMINIMUMMAXIMUMMODEHz4currently programmed maximum motor speed value is shown on the 3-D
Page 186.7 Measuring the Pump’s Output - Volumetric Test.This volumetric test will take into account individual installation factors such as line pres
Page 19Confirm the FVS flow range - The Flow Verification Sensor (FVS) will only function within its operating range. Sensor model FV-100-6V has an op
Page 2 C-1100VTABLE OF CONTENTS1...Introduction ...32...Specific
Page 21 PUMP HEAD AND VALVE EXPLODED VIEWC-1100VCAUTION: Proper eye and skin protection must be worn when installing and servicing t
Page 207.0 How to Maintain the Pump7.1 Routine Inspection and MaintenanceThe pump requires very little maintenance. However, the pump and all accesso
Page 22 C-1100VReplacement Parts Drawing52626163686650514952464544214687910111314151733423516693130475153646760565565544859574134363537403938252824232
Page 23C-1100VItem Part No Description Qty1 C-345S Screen, FootValve, P.P. 12 90002-214 Body, FootValve, PVDF 13 2-108A O-ring, FootValve, Aflas 12-10
Page 24 C-1100VUsers of electrical and electronic equipment (EEE) with the WEEE marking per Annex IV of the WEEE Directive must not dispose of end of
Page 25AUTHORIZED SERVICE CENTERSC-1100VARKANSAS NEW YORKBT Environmental, Inc Sherwood Specialties, Rice Pump & Motor Bill Thomason Inc.Repair
Page 26This page blankC-1100V
Page 27This page blankC-1100V
# 80000-387 Rev. 09/18/20125300 Business DriveHuntington Beach, CA 92649USAPhone: 714-893-8529 FAX: 714-894-9492E mail: [email protected] o
2.0 SpecificationsMaximum Working Pressure 150 psig / 10.4 bar (most models)o o Maximum Fluid Temperature 130 F / 54 Co oAmbient Temperature Range
5.0 InstallationNote: All diagrams are strictly for guideline purposes only. Always consult an expert before installing the pump into specialized sy
CAUTION: Proper eye and skin protection must be worn when installing and servicing the pump.CAUTIONADJUST WHILE RUNNINGDISCHARGE LINE
C-1100VPage 65.3 External Input Signal Connections The pump will accept any one of three different types of external input signals; 4-20 mA , 0-10 VDC
C-1100V Page 7 CIRCUIT BOARD CONNECTIONSAC sine wavesJumper Not Installed(open - factory default)Digital square wavesJumper InstalledDCMOTORBLACK (-)
Page 85.4 How To Install the Tubing and Fittings ! Inlet Tubing - Locate the inlet fitting of the pump head. Remove the tube nut. Push the clear suc
CAUTION: Proper eye and skin protection must be worn when installing and servicing the pump.Page 9Discharge Tube(Rigid P.E.)Outlet Ad
Comments to this Manuals