®MODEL A-100NE Peristaltic Injector PumpOperating Manual5300 Business DriveHuntington Beach, CA 92649USAPhone: 714-893-8529 FAX: 714-894-9492E mai
A-100NE Page 11Confirm the FVS flow range - The Flow Verification Sensor (FVS) will only function within its operating range. Sensor model FV-100-6V h
A-100NE Page 11Confirm the FVS flow range - The Flow Verification Sensor (FVS) will only function within its operating range. Sensor model FV-100-6V h
! Enable and Program the TFD and FVS Systems The TFD and FVS systems must be enabled. + Set the pump for mode 0. Press the MODE button until MODE 0 is
! Enable and Program the TFD and FVS Systems The TFD and FVS systems must be enabled. + Set the pump for mode 0. Press the MODE button until MODE 0 is
6.4 Mode 2 - 4-20 mA input - In this mode, the on-time of the cycle will automatically adjust to match the received mA input value. When the mA input
6.4 Mode 2 - 4-20 mA input - In this mode, the on-time of the cycle will automatically adjust to match the received mA input value. When the mA input
6.5 Mode 3 - 0-10V DC input - In this mode, the on-time of the cycle will automatically adjust to match the received VDC input value. When the VDC val
6.5 Mode 3 - 0-10V DC input - In this mode, the on-time of the cycle will automatically adjust to match the received VDC input value. When the VDC val
6.6 Mode 4 - Frequency (Hz) input - In this mode, the on-time of the cycle will automatically adjust to match the received Hz input value. When the Hz
6.6 Mode 4 - Frequency (Hz) input - In this mode, the on-time of the cycle will automatically adjust to match the received Hz input value. When the Hz
TABLE OF CONTENTS1...Introduction ...32...Specifications...
6.7 Mode 5 - Pulse input (Batch) - In this mode, when the total number of accumulated pulses is equal to the programmed pulse input value (Hz) , the p
6.7 Mode 5 - Pulse input (Batch) - In this mode, when the total number of accumulated pulses is equal to the programmed pulse input value (Hz) , the p
A-100NEPage 22Remove the Old Pump Tube - The pump roller assembly spins in a counter clockwise direction. The pump head inlet (suction) side is locat
A-100NEPage 22Remove the Old Pump Tube - The pump roller assembly spins in a counter clockwise direction. The pump head inlet (suction) side is locat
A-100NEPage 243945484615161337384030172627956101228292524232220211918OPTIONALQUICKCONNECT353631333234652547855531131451502ADJUST CYCLEWHEN LITTOTALTIM
A-100NEPage 243945484615161337384030172627956101228292524232220211918OPTIONALQUICKCONNECT353631333234652547855531131451502ADJUST CYCLEWHEN LITTOTALTIM
A-100NEPage 26Users of electrical and electronic equipment (EEE) with the WEEE marking per Annex IV of the WEEE Directive must not dispose of end of l
A-100NEPage 26Users of electrical and electronic equipment (EEE) with the WEEE marking per Annex IV of the WEEE Directive must not dispose of end of l
# 80000-358 Rev. 09/18/20125300 Business DriveHuntington Beach, CA 92649USAPhone: 714-893-8529 FAX: 714-894-9492E mail: [email protected] o
TABLE OF CONTENTS1...Introduction ...32...Specifications...
5.0 InstallationNote: All diagrams are strictly for guideline purposes only. Always consult an expert before installing the pump into specialized s
5.0 InstallationNote: All diagrams are strictly for guideline purposes only. Always consult an expert before installing the pump into specialized s
A-100NEPage 65.3 External Input Signal Connections The pump will accept a variety of external control input signals; 4-20 mA , 0-10 VDC, TTL, CMOS, AC
A-100NEPage 65.3 External Input Signal Connections The pump will accept a variety of external control input signals; 4-20 mA , 0-10 VDC, TTL, CMOS, AC
A-100NEPage 85.4 How To Install the Tubing and Fittings ! Inlet Tubing - Locate the inlet fitting of the Pump Tube. Remove the tube nut. Push the cl
A-100NEPage 85.4 How To Install the Tubing and Fittings ! Inlet Tubing - Locate the inlet fitting of the Pump Tube. Remove the tube nut. Push the cl
Comments to this Manuals